As a short disclaimer, the Centauri X Ultra has not been released yet and Elegoo has not published a full specification sheet. This article is therefore based on Elegoo’s press release and the specification panel shown at its Formnext booth, not on personal experience using the machine, and the figures may still change before release.
Elegoo used Formnext 2026 in Frankfurt to give the first public look at the Centauri X Ultra, its first 3D printer with multiple independent printheads. The company’s press release on 17 November describes it as an upcoming FDM printer with four independent printheads, and says quick printhead switching helps minimise material waste during colour changes. The release does not include a price, a launch date or detailed specifications, so most of what is known so far comes from the display panel next to the printer and from the press who saw it on the show floor.

How the Centauri X Ultra differs from CANVAS
Elegoo’s current multicolour option is the CANVAS system on the Centauri Carbon 2, which feeds up to four filaments into a single nozzle. Because every filament shares the same nozzle, the old colour has to be purged out each time the printer switches. The Centauri X Ultra carries four complete printheads instead and swaps the whole head, which Elegoo says takes 5 seconds. When each head is loaded with its own colour or material, there is no previous filament to flush at a colour change, and this is where the claimed waste saving comes from.
The panel also lists support for up to 20 colours through a system called AFS. Elegoo has not explained what AFS is, how it connects to the printer or how much it will cost. Since four heads can only hold four filaments at a time, a print with more than four colours means reloading at least one head, which brings purge waste back into the process. The zero-purge claim therefore only applies when each head keeps a single colour throughout the print. Toolchangers in this class, including the Snapmaker U1, also still print a small prime tower to keep idle nozzles primed, so a zero-purge claim does not mean the printer produces no waste at all.
Built-in filament drying
Filament is stored in two clear compartments on the sides of the printer, each holding two spools, and both can be heated up to 65°C to dry the filament. According to the datasheet reported by China-Gadgets, the drying compartments and the top cover are included as standard. The compartments also read RFID tags and handle automatic loading and recovery.
The 65°C figure applies to the filament compartments only. Elegoo has not said whether the print chamber itself is actively heated, so the X Ultra should not be described as having a heated chamber until that is confirmed.
Preliminary Centauri X Ultra specifications
Elegoo’s press release only confirms the four independent printheads and support for rigid and flexible materials. The rest of the figures below come from the specification panel at the Formnext booth.
| Specification | Shown at Formnext 2026 |
|---|---|
| Printheads | 4 independent printheads |
| Printhead change time | 5 seconds |
| Multicolour | 4 colours natively, up to 20 with AFS |
| Build volume | 256 × 256 × 256 mm |
| Max print speed | 500 mm/s |
| Max nozzle temperature | 350°C |
| Max bed temperature | 120°C (100°C in 3.5 minutes) |
| Extruder | Dual-gear direct drive, 7:1 ratio |
| Filament drying | 2 compartments, 2 spools each, up to 65°C |
| Supported materials | PLA, PETG, TPU, ABS, PA, PC |
| Display | 5-inch flip-up touchscreen |
| Dimensions | 613 × 462 × 510 mm including filament compartments |
| Other features | Auto calibration, active vibration compensation, RFID, auto loading and recovery, Cooling Mode for PLA and PETG, quiet mode |
The 256 mm build volume is the same as the Centauri Carbon and Centauri Carbon 2, and the 350°C nozzle temperature matches the Centauri Carbon 2, so the X Ultra looks like a continuation of the Centauri platform rather than a larger machine. Elegoo says rigid and flexible filaments can be combined in one print. Abrasive filaments such as carbon fibre blends are not on the material list, and the nozzle type has not been disclosed.
How it compares to other four-tool 3D printers
The closest competitors are the four-tool printers already on sale from Snapmaker, Flashforge and Creality. The Snapmaker U1 and Flashforge Creator 5 Pro swap complete toolheads like the X Ultra, while the Creality K3 swaps nozzle assemblies through its KliTek system, but all three keep four filaments loaded in four independent paths. The prices below are from each brand’s official US store, checked on 21 November 2026, and the U1 and Creator 5 Pro prices are Black Friday offers.
| Printer | Build volume | Nozzle / bed max | US price |
|---|---|---|---|
| Elegoo Centauri X Ultra | 256 × 256 × 256 mm | 350°C / 120°C | Not announced |
| Snapmaker U1 | 270 × 270 × 270 mm | 300°C / 100°C | $699 (Black Friday, until 1 December) |
| Flashforge Creator 5 Pro | 256 × 256 × 256 mm | 320°C / 120°C | $749 (Black Friday, until 30 November), regular $949 |
| Creality K3 | 260 × 260 × 260 mm | 300°C / 100°C | $849 |
| Printer | Enclosure | Filament drying |
|---|---|---|
| Elegoo Centauri X Ultra | Enclosed, top cover included | 2 heated compartments, 65°C |
| Snapmaker U1 | Top cover optional | Not stated |
| Flashforge Creator 5 Pro | Enclosed, 65°C actively heated chamber | Not stated |
| Creality K3 | Open top, top cover optional | Not stated |
On paper, the X Ultra has the highest nozzle temperature of the four and matches the Creator 5 Pro on bed temperature. The U1 still has the largest build volume, and the Creator 5 Pro is the only one confirmed to have an actively heated chamber. The drying compartments and the included top cover are the clearest differences between the X Ultra and the U1, which sells its top cover separately.
Price will matter more than any of these specifications. During Black Friday the U1 is $699 and the Creator 5 Pro is $749, while the K3 is $849. If the X Ultra launches close to the US$1,000 ceiling that All3DP has reported, it would cost more than all three at today’s prices, although the gap would narrow once the Black Friday offers end, since Flashforge lists the Creator 5 Pro at $949 outside the sale and Snapmaker refers to a $999 launch price for the U1. The final price will decide whether the drying compartments and higher nozzle temperature are enough to justify any difference.
Price and release date
Elegoo has not announced either. All3DP, which saw the printer at the show, reports that Elegoo is targeting a Q1 2027 release at a price below US$1,000. The only Q1 2027 date in Elegoo’s own press release belongs to the Saturn 5 Ultra resin printer, so the X Ultra timing should be read as a report from the show floor rather than a commitment from Elegoo.

What is still unknown
Several important details have not been shared yet:
- How the printheads are docked, locked and calibrated, and whether tool offset calibration is automatic
- What AFS is, how it distributes up to 20 colours across four heads, and whether it is related to CANVAS
- Whether the print chamber is actively heated
- The nozzle type, whether nozzles are user-replaceable, which diameters are offered and whether abrasive filaments are supported
- Which TPU hardness the printer can feed reliably, since one observer who photographed the machine noted that the PTFE tube routing near the toolhead looks tight
- Maximum acceleration, camera and the full sensor list
- The final price, the bundle contents and the release date
What to watch for next
With the Centauri X Ultra, Elegoo joins Snapmaker, Flashforge and Creality in offering a four-head printer aimed at home users. On paper it stands out for including the drying compartments and top cover as standard and for its 350°C nozzle, but none of these claims have been tested independently and the price is still open. The 350°C rating also says little on its own about how well the printer will handle engineering filaments such as PA and PC, because chamber temperature and the build plate matter just as much, and Elegoo has not said whether the chamber is heated or which build plate the printer uses. The two things to watch are where the final price lands against the U1, K3 and Creator 5 Pro, and how reliable the printhead switching and filament routing turn out to be once review units are available. We will update this article when Elegoo confirms the price and full specifications.
Sources
- ELEGOO Showcases New Solutions Across Resin Printing, FDM Printing and 3D Scanning at Formnext 2026, PR Newswire
- Elegoo Debuts Centauri X Ultra Toolchanger at Formnext, All3DP
- The Best New Desktop & Industrial 3D Printers from Formnext 2026, All3DP
- ELEGOO’s Toolchanger Is Here! Centauri X Ultra vs. CC2 and emoji, Psych0h3ad
- Elegoo Centauri X Ultra: 4-Kopf-Toolchanger mit Trockenboxen, China-Gadgets
- Snapmaker U1 Specifications, Snapmaker
- Black Friday 3D Printer Deals 2026, Snapmaker
- Snapmaker U1 Drops to $699 This Black Friday, All3DP
- Flashforge Creator 5 Pro, Flashforge
- Flashforge Black Friday Sale, Flashforge
- The Coming Toolchanger Price War Could Challenge Bambu Lab, Fabbaloo
- The Creality K3 Aims to Cut Multicolor Waste by 85% with 5-Second Nozzle Swaps, All3DP
Don’t miss the latest articles and guides
Get new Domechy articles, guides and free models straight to your inbox.
Wanna share your thoughts or request anything? Comment below.